Cissell MANHD170 Manuel du propriétaire

Page 1MANHD170 3/06Technical specificationsInstallation instructionsOperating instructionsMaintenanceCissell Manufacturing Co.831 S. First St. -

Page 10UNPACKING/GENERAL INSTALLATION (ALL DRYERS)This dryer is packed in a large wooden crate.Upon arrival of the equipment, any damage in shipment s

Page 11GENERAL INSTALLATION (ALL DRYERS)IMPORTANTProvide adequate clearance for air openings into thecombustion chamber.Replacement parts for this dry

Page 12GAS DRYER DIMENSIONS

Page 13STEAM DRYER DIMENSIONS

Page 14GENERAL Floor Space ...64” (1626 mm) Deep x 54”SPECIFICATIONS (1372 mm) Wide x 96”FOR 150 lb. DRYERS (

Page 15Operating Steam Pressure 100 psig (6.9 bar) MaximumBoiler HP 12.5 HP (9.33 kW)Heat Capacity 8 CoilSteam Coils (4) 6”(153 mm) x 10 1/4” (261 mm)

Page 16ELECTRICAL CONNECTIONS (WITH GROUNDING INSTRUCTIONSELECTRICALCONNECTIONSFOR ALL DRYERSDryers must be electrically grounded by a separate #14 or

Page 17The size of the gas service pipe is dependant upon many variables, suchas tees, lengths, etc. Specific pipe size should be obtained from the ga

Page 18GAS PIPING INSTALLATION (ILLUSTRATION)

Page 19GAS PIPE SIZE CHARTTOTAL BTU/HR(for LP Gas correcttotal Btu/h below bymultiplying by .6)TOTALKCALHOURGAS PIPE SIZE FOR 1000 Btu (252 kcal/h) NA

Page 2For optimum efficiency and safety, we recommend that you read the Manual before operating the equipment. Store this manual in a fileor binder an

Page 201. The installation must conform to local codes or in absence of localcodes, with the National Fuel Gas Code, ANSI Z223.1 orthe CAN/CGA-B149, I

Page 21Steam Dryers - Option Installation Instructions (When The Steam Bonnet Is Shipped Separate)1. The dryer comes in two wood crates:A - Very large

Page 22I - Control Box Assembly and II - Steam Bonnet Assembly(When The Steam Bonnet Is Shipped Seperate)I - Control Box Assembly II - Steam Bonnet As

Page 23STEAM PIPING - 1. Set and anchor dryer in position. Machine should be levelINSTALLATION assure proper steam circulation.INSTRUCTIONS2. To prev

Page 24STEAM PIPING INSTALLATIONINDIVIDUALLY TRAPPED COILS ARE RECOMMENDED RATHER THAN MANFOLDING RE-TURN INTO ONE TRAP.

Page 25DRYER INSTALLATION WITH MULTIPLE EXHAUSTFor Exhaust Duct less than 14 feet (5 m) and 2 elbowsequivalent and less than 0.3 inches (.8 mbar) stat

Page 26DRYER INSTALLATION WITH MULTIPLE EXHAUST (ILLUSTRATION)

Page 27For Exhaust Duct more than 14 feet (5 m) and 2 elbows equivalentand more than 0.3 inches (8 mm) static pressure.1. Make-up air from outside bui

Page 28Dryer Dryer Pocket Maximum Air Flow Duct Size For Required Make-upModel Capacity Rate per Pocket Service Connection

Page 29DRYER INSTALLATION WITH SEPARATE EXHAUST (PREFERRED)DRYER INSTALLATION WITH SEPARATE EXHAUST(PREFERRED)For Exhaust Duct less than 14 feet (5 m)

Page 3WARNING: To avoid fire hazard, do not dry articles containing foam rubber or similar texturematerials. Do not put into this dryer flammable ite

Page 30Nothing is more important than air flow for the proper operation of a clothes dryer. Adryer is a pump which draws make-up air from the out-of-d

Page 31RULES FOR SAFE OPERATION OF DRYERRULES FOR SAFEOPERATION OF DRYER1. Be sure your dryer is installed properly in accordance with therecommended

Page 32ENERGY SAVING TIPSENERGY SAVING TIPSABOVE 2,000 FEET(610 M)1. Install dryer so that you can use short, straight venting. Turnedelbows and long

Page 33OPERATING INSTRUCTIONS—TWO TIMER MODELS

Page 34OPERATING INSTRUCTIONS—TWO TIMER MODELS OPERATING INSTRUCTIONS—TWO TIMER MODELS1. After loading the dryer with the water washed clothes load,cl

Page 35OPERATING INSTRUCTIONS—TWO TIMER MODELSOPERATINGINSTRUCTIONS—TWOTIMER MODELS OPERATING INSTRUCTIONS—TWO TIMER MODELS(continued)What is happenin

Page 36To help you troubleshoot the dryer, listed below are the most commonreasons for service calls and some answers to the problems. Before youcall

Page 37TROUBLESHOOTING CHARTTROUBLE CAUSE REMEDYCheck fuses on circuit breakers. Make sure main controlswitch is ON.Check power source; voltage, phas

Page 38Check for correct control voltage - 24V.Check power supply, check secondary voltage on transformerand check wiring and wiring diagram.Close lin

Page 39Blow out.Adjust gas pressure per rating plate.Send to factory for correct orifices.Clean exhaust.Check ground.Replace orifices. Check factory

Page 4 ATTENTION: L’ACHETEUR DOIT PLACER L’AVERTISSEMENT SUIVANT DANS UN ENDROIT CLAIR ET VISIBLE:AVERTISSEMENT. Assur

Page 40NOTE: Some models are equipped with a dual ignition system.The dual ignition system contains two Direct SparkIgnition modules in parallel. Eac

Page 41DIRECT SPARK IGNITION OPERATION FLOW CHART

Page 42MAINTENANCE—GENERALCLEAN LINT TRAP DAILY. Remove lint before starting day’s operation. A clean lint trap will increasethe efficiency of the dr

Page 43BURNER AIR INLET ADJUSTMENTBURNER AIR INLETADJUSTMENT

Page 44BASKET ALIGNMENT FOR DRYERS WITH TM200 GEAR REDUCER

Page 45INSTRUCTIONS1. Loosen bolts number one (1) through five (5).2. Place pin “A” in position shown in figures 1 and 2.3. Check pins “B” at position

Page 46BASKET ALIGNMENT FOR DRYERS WITH GEAR MOTORJacket Rear ViewBASKET TOO LOW If there are shims under Bearing B;1. Loosen bolts2. Remove shim(s).

Page 47SHIMMING THE BASKET AND SPIDER ASSEMBLYINSTRUCTIONS FORSHIMMING THE BASKETAND SPIDER ASSEMBLYThis procedure is normally necessary when replacin

Page 48AIR SWITCH ADJUSTMENTAIR SWITCHADJUSTMENT1. Shut off current; disconnect leads and remove air switch.2. Lay air switch assembly on flat surface

Page 49InstructionsIn operation, coasting of basket increases, making it necessary toreadjust reversing timer.CAUTIONFailure to do this will cause the

Page 5The Cissell Manufacturing Company (Cissell) warrants all new equipment (and the original parts thereof) to be free from defectsin material or wo

Page 50DRYERS WITH REVERSING CONTROLInstructionsNOTEFan rotates counter-clockwise as viewed from back end ofmotor. See arrow on motor support.Basket r

Page 51LARGE GEAR REDUCER MAINTENANCELARGE GEAR REDUCER MAINTENANCEBefore placing the dryer in operation, check the oil level. If the oil levelis corr

Page 52FRONT VIEWRef.No. Part No. Description2 TU9608 Basket and Spider Assembly (Galvanized) (TM200 Gear Reducer)TUS9608 Basket and Spider Asembly (S

Page 53REAR VIEW (TM200 GEAR REDUCER)See following page forpart numbers. To Gear Motor.

Page 54REAR VIEW (TM200 GEAR REDUCER)1 TUX415 Air Switch Cover3 TU8206 Air Switch Assembly5 TU9663 Gear Sheave (50/60 Hz.)6 TU3807 Sheave Bushing7 TU1

Page 55REAR VIEW (GEAR MOTOR)See following page forpart numbers. To Gear Motor. To Fan Motor.

Page 56REAR VIEW (GEAR MOTOR)1 TUX415 Air Switch Cover3 TU8206 Air Switch Assembly5 TU3418 Washer, Lock, 5/8”6 TUX328 Nut, Hex, 5/8-117 TU16046 Beltgu

Page 57TU15449 FRONT PANEL ASSEMBLY* Cover plate used for DMP and PRO HC.**1 EA-00652-0 Reed Switch2 SB-00975-0 #6-32 Screw3 PIF172 Hinge post bearin

Page 58THERMOSTAT ASSEMBLY - 2 TIMERTU6030 Assembly, Thermostat1 TU5530 Mounting Bracket2 TU1980 Thermostat3 TU3593 ThermometerTU3816 Lens Replacemen

Page 59BURNER ACCESS DOORRef.No. Part No. DescriptionTU14624 - Burner Access Door complete (Specify color)1 CA-13098-0 Gasket, DR dryer control doors2

Page 6TABLE OF CONTENTS PAGEModel Numbers & Company Address ...

Page 60LINT DOOR ASSEMBLYRef.No. Part No. DescriptionTU14627 Lint Door Complete (Specify color)1 LA-00123-0 Latch2 SB-00836-0 Screw, Pancake3 SB-009

Page 61DMP SENSOR ASSEMBLYRef. Part No. DescriptionNo.TU15538 DMP Thermostat Assembly1 TU15537 Bracket2 EA-00411-0 Switch - 220 degrees3 TU11991 Therm

Page 622 TIMER SENSOR ASSEMBLYRef.No. Part No. DescriptionTU6029 - Thermostat Assembly1 TU2477 Thermostat #AR5942 TU2486 Bracket3 TU3801 Nut, speed #C

Page 63Ref.No. Part No. DescriptionESA-00940-0 Sensor Assembly1 254/00009/10 Thermistor2 CA-23067-0 Thermostat3 EA-00411-0 Switch, 220 Degrees4 SB-008

Page 64Ref.No. Part No. DescriptionTU14723 PROHC Sensor assembly (lower)1 CA-13067-0 Bracket (sensor)2 EA-00594-0 Switch, 220 degrees3 SB-00828-0 Scr

Page 65AIR SWITCH ASSEMBLYRef.No. Part No. DescriptionTU8206 Assembly, Air Switch1 F888 E-Ring2 TU1770 Insulator3 TU1771 Tinnerman Nut, #64 TU2463 Act

Page 662 TIMER CONTROL PANEL ASSEMBLYRef. Part Ref. PartNo. No. Description No. No. Description1 ET208 #6-32 x 1/4” Binding Hd Screw2 F1300 24V Relay3

Page 67DMP CONTROL PANEL ASSEMBLYRefNo. Part No. Description1 TU14469WHT DMP Control Panel Welded Assembly2 TU15184 Opl Dmp, Rt-Side (Dn) Overlay3 TU1

Page 68Ref.No. Part No. Description1 254/00039/00 Overlay2 254/00070/00 Pro Control3 M261 #8-32 Screw4 M270 Lockwasher5 TU14435 Emergency Stop (50 Hz)

Page 69PROHC CONTROL PANELRef.No. Part No. Description1 254/00018/00 Overlay2 254/00070/00 ProHC Control3 M261 #8-32 Screw4 M270 Lock Washer5 TU14435

Page 7TABLE OF CONTENTSAir Switch Assembly ...

Page 70Ref.No. Part No. Description1 TU13700 Plate, Motor Control2 TU13802 Transformer, 115/208/230 75VATU13514 Transformer, 60VA 460V/24V 60VATU13642

Page 71PARTS—TM200—LARGE GEAR REDUCER WITH BRONZE TEETH1 TM203 Housing2 K474 Oil Level Plug Kit3 TM119 1/4” Vent Plug4 TM208 Small Bearing Cone &

Page 72GAS BONNET AND BURNER ASSEMBLYREF PART DESCRIPTION REF PART DESCRIPTIONNO. NO.. NO. NO.TU15763 - Natural Gas BonnetTU15767 - LP Gas Bonnet1 TU1

Page 73 STEAM BONNET ASSEMBLY—TU1402713 TU2847 Flat Washer (Pkg. of 6)14 TU9953 Air Filter 20” x 24” x 1”15 TU9873 Steam Bonnet Weldment16 CB36 1/4” -

Page 74INSULATION PLACEMENTRef. Part No. DescriptionNo.1 TU15766 Insulation, Front Panel (Set)2 TU15764 Insulation3 TU15765 Insulation4 TU15774 Insula

Page 75

Page 8The following symbols are used in this manual and/or on the machine.Symbol DescriptionNOTE!onmarcheEinconectadooffarrêtAusdesconectadoHot! Do N

Page 9rotation in two directionsrotation dans les deux sensDrehbewigung in zwei Richtungenmovimiento rotativo en los dossentidosEnd of Cyclecautionatt